4 Buttons rechargeable Remote Z-Wave Plus - Hank

34,95

Taxas não incluidas: € 28,88

Disponibilidade:
Em Stock
Código do produto:
ES-72-HAN-HKZW-SCN04
Fabricantes:
Hank

Descrição

The Hank Z-Wave Plus Scene Controller is a wireless, portable and rechargeable device. It can control Z-Wave devices, such as a smart plug or intelligent dimmer after being included in a Z-Wave controller. You can also use it to activate scenes. This stage controller can perform 3 different actions per button, depending on the type of support: short press, support maintained, support released. Operating with a rechargeable battery with a range of 3 to 6 months, it will be very easy to recharge by connecting a USB cable on its micro-USB port. No need to change the batteries! In addition, this stage controller is equipped with a buzzer that will alert when the battery is low (less than 20%), or when communication has failed. An RGB LED is present to give visual information.

This stage controller is also equipped with the Z-Wave scope test function. A Z-Wave controller (remote control, dongle ...) is required to integrate this module into your network if you already have an existing network. ç

FUNCTIONS:

  • Z-Wave + Scene Controller
  • Control up to 3 devices / scenes per button
  • Z-Wave Range Test Function
  • Rechargeable battery
  • Low battery warning and communication error (via buzzer)
  • Security of radio communication via AES-128 encryption
  • Integrates the Z-Wave 500 series chip
  • Firmware Updates Over The Air (OTA)
  • Ease of use and installation

  TECHNICAL CHARACTERISTICS :

  • Module Type: Z-Wave + 500 Series Transmitter
  • Power supply: 3,6V rechargeable battery LIR2450
  • Standby power consumption: 3uA
  • Power consumption in operation: 36mA
  • Frequency: 868.42 Mhz
  • Transmission distance: 100m in free field, 30m indoors
  • Dimensions: 50 x 50 x16 mm
  • Operating temperature: 0 ° C to 40 ° C
  • Certifications: FCC, CE, Z-Wave
  • Z-Wave certification number: ZC10-16095219

Manual:

Especificação

Compatibilidade controlador principal
eeDomus+ Full Compatible
Fibaro Home Center 2 v4.160 Not Tested
Fibaro Home Center Lite v.4.160 Not Tested
Vera Edge / Plus Not Tested
Zipabox/Zipamini/ZipaTile Not Tested
Piper / Piper NV (v.1.7.1) Not Tested
Indigo Not Tested
jeedom Full Compatible
Z-Wave.me / Z-Way / PoPP Hub Not Tested
Domoticz Not Tested
ZiHome Not Tested
Somfy Tahoma Not Tested
Home Assistant Not Tested
Telldus Not Tested
Tech Data
IP Rating IP20
FLiRS No
Power Supply Batterie rechargeable 3,6V LIR2450
Explorer Frames - NWI Support No
SDK 6.51.08
App Version HW: 1 FW: 1.00
Device Type Wall Controller
Z-Wave Alliance Product Link https://products.z-wavealliance.org/products/1968
Procedures
Incluison Included as non-secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Waave network controller operating manul). 3. Triple click a button. 4. If the inclusion is successful, the LED will blink in blue less than for 5 seconds and then keep on for 15 seconds. Included as a secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual). 3. Pressing and holding a button for 3 seconds. 4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds.
Exclusion To remove the Scene Controller from the Z-Wave network: (1) Insert the LIR2450 battery. (2) Set the Z-Wave network main controller into remove mode (see Z-Wave controller operating manual). (3) Triple click the a button, if the exclusion is successful, LED will blink in orange for less than 5 seconds and then keep on for 3 seconds.
Factory Reset Pressing and holding a button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds. Using this procedure only in the event that the network primary controller is missing or otherwise inoperable.
Wake Up Pressing and holding a button for 3 seconds. Led will turn to green, which means Scene Controller has been woken up.

Perguntar

Fazer uma pergunta ou comentário

Obs: HTML não é suportado!

Mau            Bom


Continuar

Z-Wave Portugal

A loja online que vende soluções para a automação das habitações através das redes sem fios e do protocolo Z-Wave. Z-Wave é o standard internacional para as redes sem fio dos sistemas de controlo para habitações. Com base nestas soluções pode gerir a iluminação, a electricidade, os estores, os alarmes e muito mais, optimizando a utilização destes meios. Os produtos Z-Wave, mesmo os de diferentes fabricantes, funcionam bem em conjunto permitindo o controlo efectivo da casa inteligente.

Contact Us

Móvel:
+351 919655531
email:
info@z-wave.pt
Skype:
ar.alexandre.ramos

Twitter

Facebook