Door and window sensor extra finestrip Z-Wave Plus - Sensative

58,00

Taxas não incluidas: € 47,93

Disponibilidade:
Em Stock
Código do produto:
ES-13-SENSA_TS312297
Fabricantes:
Sensative

Descrição

This strips from manufacturer Sensitive, is ther wireless magnetic sensor for door and window thinnest in the world! It is so thin that it can be mounted invisibly on most windows and doors.

The Strips uses a magnetic sensor for detecting whether a window / door is open or closed. With a strips on every window and door, you get a complete perimeter protection. With Strips, you can easily check that all windows and doors are closed, it alerts you if something unexpected happens and it is connected with other devices in the  smart home using the Z-Wave Plus  technology.

Simple and invisible assembly: No need to drill or lay cables! With a little less than 3 mm, the sensor is integrated invisibly between the door / window and its frame. All you have to do is connect the Strips to a Z-Wave controller, and then use the adhesive mount to attach the magnet to the door or window and the sensor on the frame.
Indoor and outdoor wse: Strips is designed for indoor and outdoor environments.
Batery: With a battery that has a life of up to ten years, it is easy to forget the sensor once it is mounted. However, the sensor keeps track of the remaining energy in the battery and will let you know when the level becomes low.
Connectivity: The Strips uses Z-Wave Plus technology. The Z-Wave home automation protocols enables communication between devices, Strips can comunitcate with you through your Smartphone. To do this you will need a Z-Wave controller to integrate the strips in your home network.

FEATURES:

  • Opening detector for door and window
  • Invisible mounting
  • Battery with battery life of 10 years
  • Waterproof
  • Low Battery Detection
  • Low power consumption
  • Ease of use and installation

SPECIFICATIONS:

  • Module type: Z-Wave Transmitter
  • Power: LiMnO2 Battery
  • Battery life: 10 years
  • Frequency: 868.42 Mhz
  • Range: up to 100 m outdoors, up to 30 m in buildings
  • Operating temperature: -30 ° C to + 80 ° C

Manuals:


Especificação

Compatibilidade controlador principal
eeDomus+ Full Compatible
Fibaro Home Center 2 v4.160 Full Compatible
Fibaro Home Center Lite v.4.160 Full Compatible
Vera Edge / Plus / Secure Full Compatible
Zipabox/Zipaminicro/ZipaTile Full Compatible
Piper / Piper NV (v.1.7.1) Not tested
Indigo Not tested
jeedom Full Compatible
Z-Wave.me / Z-Way / PoPP Hub Full Compatible
Domoticz Not tested
ZiHome Not Tested
Tech Data
IP Rating IP 44
Power Supply 3.0V LiMnO2 not changeable. 10 years long
Explorer Frames - NWI Support No
SDK 6.51.06
App Version
Device Type Notification Sensor
Peper1 Database link http://www.pepper1.net/zwavedb/device/831
Z-Wave Alliance Product Link http://products.z-wavealliance.org/products/2073
Procedures
Incluison Strips is delivered in "auto-add" mode. Follow the process below to add Strips in a Z-Wave network. 1. Start the add mode on the Z-Wave controller. See the controller’s manual. 2. Remove both magnets from Strips. Strips blinks twice to confirm the command and successful addition. 3. A long LED blink indicates that the add process was successful 4. The Z-Wave controller application should now allow you to monitor your Strips sensor status. 5. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly. 6. If the Z-Wave system does not respond, it may be needed to change Strips’ notification type. Manual add: 1. Set the controller to add mode (See your controller’s manual). 2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the add process was successful.
Exclusion 1. Set the controller in remove mode (See your controller’s manual). 2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the remove process was successful.
Factory Reset In order to reset Strips (possible when the connection to the controller is lost or inoperable): 1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. On the 3rd repetition, leave the magnet at the rounded edge for 10s. 4. A long LED signal indicates success.
Wake Up Wake up Strips manually for Z-Wave communication: 1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. 3. Repeat 3 times in total within 10 seconds.

Perguntar

Fazer uma pergunta ou comentário

Obs: HTML não é suportado!

Mau            Bom


Continuar

Z-Wave Portugal

A loja online que vende soluções para a automação das habitações através das redes sem fios e do protocolo Z-Wave. Z-Wave é o standard internacional para as redes sem fio dos sistemas de controlo para habitações. Com base nestas soluções pode gerir a iluminação, a electricidade, os estores, os alarmes e muito mais, optimizando a utilização destes meios. Os produtos Z-Wave, mesmo os de diferentes fabricantes, funcionam bem em conjunto permitindo o controlo efectivo da casa inteligente.

Contact Us

Móvel:
+351 919655531
email:
info@z-wave.pt
Skype:
ar.alexandre.ramos

Twitter

Facebook