€ 49,99
Taxas não incluidas: € 41,31
Descrição
Opening sensor Z-Wave + Fibaro Door / Window Sensor 2
The Fibaro Door / Window Sensor 2 sensor is a battery-powered, Z-Wave Plus compatible wireless magnetic contact sensor. The opening is detected by separating the sensor body and the magnet. The sensor can be used to trigger scenes and wherever information about opening or closing doors, windows, garage doors, etc. is required. In addition, the Fibaro Door / Window Sensor 2 is equipped with an integrated temperature sensor.
Contact Sensor
The Fibaro Door / Window Sensor 2 is easily mounted on doors, windows, garage doors, gates, roller shutters, closets, and more.
Temperature sensor
Control the temperature throughout your home. The Fibaro Door / Window Sensor 2 measures the temperature thanks to its built-in temperature sensor.
Protection against sabotage
For safety reasons, the Fibaro Door / Window Sensor 2 housing is protected against opening or destruction.
FUNCTIONS
- Opening sensor Integrated temperature sensor Z-Wave Plus Compatible
- Button to include / exclude detector
- Low battery detection
- Protection against sabotage
- Led indicator to indicate the status of the detector
- Available in 7 colors
- Very small, small dimensions
- Ease of use and installation
TECHNICAL CHARACTERISTICS
- Module Type: Z-Wave Transmitter
- Power supply: Battery ER14250 (1 / 2AA) 3.6VDC (included)
- Battery life: Approximately 2 years (with default settings)
- Frequency: 868.42 Mhz
- Transmission distance: 50m free field, 40m indoor
- Dimensions: 71 x 18 x 18 mm
- Operating Temperature Range: 0-40 ° C
- Temperature measurement range: 0 - 60 ° C
- Accuracy of temperature measurement: ± 0.5 ° C
- Certifications: RoHS 2011/65 / EU R & TTE 1999/5 / WE
MANUAL
Especificação
| Compatibilidade controlador principal | |
|---|---|
| eeDomus+ | Full Compatible |
| Fibaro Home Center 2 v4.160 | Full Compatible |
| Fibaro Home Center Lite v.4.160 | Full Compatible |
| Vera Edge / Plus / Secure | Full Compatible |
| Zipabox/Zipaminicro/ZipaTile | Full Compatible |
| Piper / Piper NV (v.1.7.1) | Full Compatible |
| Indigo | Compatible (Testing) |
| jeedom | Full Compatible |
| Domoticz | Full Compatible |
| ZiHome | Full Compatible |
| Vera 3 | Full Compatible |
| Vera Lite | Full Compatible |
| Tech Data | |
| Power Supply | Batery ER14250 3.6V |
| SDK | 6.51.06 |
| App Version | 3.2 |
| Device Type | Routing Binary Sensor |
| Z-Wave Alliance Product Link | http://products.z-wavealliance.org/products/1356 |
| Procedures | |
| Incluison | 1) Open the cover. 2) Remove the battery blocker. 3) Close the cover. 4) Locate the sensor nearby the main Z-Wave controller. 5) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 6) Quickly, triple click the TMP button located on the bottom of the casing. 7) Wait for the device to be added to the system. Successful adding will be confirmed by the controller. 9) Install the device using the attached self-adhesive pads. 1) Open the cover. 2) Remove the battery blocker. 3) Close the cover. 4) Locate the sensor nearby the main Z-Wave controller. 5) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 6) Quickly, triple click the TMP button located on the bottom of the casing. 7) Wait for the device to be added to the system. Successful adding will be confirmed by the controller. 9) Install the device using the attached self-adhesive pads. |
| Exclusion | 1) Place the device within direct range of the Z-Wave controller. 2) Make sure that Sensor's cover is closed. 3) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 4) Quickly, triple click the TMP button. 5) Wait for the device to be excluded from the system. Successful exclusion will be confirmed by the controller. |
| Factory Reset | Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. 1) Take off the Sensor's cover and remove battery. 2) Install the battery while holding both TMP buttons (after mounting the device, one button is constantly pressed by the cover). 3) Release the TMP button within 5 seconds. 4) LED will blink 3 times to confirm launching of reset procedure. 5) Reset procedure may last up to 30 seconds. Do not remove the battery until reset is complete. 6) Reset will be confirmed by the six blinks of the LED. |
| Wake Up | FIBARO Door/Window Sensor will wake up at a defined time interval and will ALWAYS try to communicate with the main controller. Setting wake up interval to 0 disables sending Wake Up Notification frame automatically. There is a possibility to wake up the device manually by a single TMP button click. |
