Universal Dimmer 250W Z-Wave+ Fibaro with metering

59,99

Taxas não incluidas: € 49,58

Disponibilidade:
Em Stock
Código do produto:
ES-31-FIB_FGD_212
Fabricantes:
Fibaro

Descrição

The in-wall micromodule FGD-212 by Fibaro  will allow you to control a lighting system thanks to the Z-Wave protocol while maintaining your existing switch. You will therefore be able to operate a connected lamp and to vary its intensity using the existing switch, or iva a Z-Wave transmitter.

The new dimmer Fibaro FGD-212 is equipped with a smart detection algorithm of the light source which facilitates the configuration and ensures a high compatibility of the device. It has a self-protection against overloading and a soft start function. In the case of non-dimmable light sources, only the ON / OFF function is possible (connection with 3 wires system).

It is compatible with any type of lamps dimmables or not:

As a dimmer: -

  • Classic Light Sources Incandescent and halogen powered by 230VAC
  • 12V halogen lamps (with electronic transformers)
  • 12V halogen lamps (with ferromagnetic transformers)
  • LED Lamps dimmables
  •  Fluorescent Lamps CFL dimmables
  •  Using the Bypass with a source of dimmable light up in  225VA 2 wires mode connection (depending on load type)

As an On/off switch:

  • Fluorescent lamps
  • LED Lamps
  • Using the Bypass module with any light source its supports up to 225VA (depending on load type)

This module  can be used in 2 wires mode  (without neutral), replacing an existing switch, or three wires mode with a conventional power supply (phase + neutral). For lamps with very low power consumption (LED lamp, for example), you can use the Bypass moduel load  Fibaro FGB-001 that allows proper operation of the module.

In addition to the function variation, this micro-module can also measure the power consumption of the connected load. Instant consumption figures (in W) and total electricity consumption (kWh) can be consulted.

A Z-Wave controller (remote, control dongle, gateway ...) is necessary to integrate this module in your Z-Wave . Each Z-Wave module functions as a wireless repeater with other modules to ensure full coverage of your home.

FEATURES:

  • Youo can manage a lighting system locally and in remote
  • Module can be installedbehind an existing switch
  • ON / OFF function and dimmer
  •  Use 2 wires mode neutral not required)
  • Integrates Z-Wave chip 500 series
  • Communication 250% faster compared to standard Z-Wave devices
  • Automatic load detection
  • Protected against overload
  • Compatible with Z-Wave and  Z-Wave Pluscontrollers
  • Function Measuring Active Power and Energy
  • Works with different types of switches - tappet, rocker, three-way, etc.
  • Soft start function (soft-start)
  • LED status indication of inclusion, and calibration levels
  • Z-Wave range tester integrated
  • Automatically detects wiring faults, high temperature, power surges and overloads
  • Advanced Configuration Options
  • Small, discreet and aesthetic
  • Ease of use and installation

SPECIFICATIONS:

  • Module Type: receiver Z-Wave
  • Power supply: 230V +/- 10%, 50Hz
  • Consumption: 1.3W
  • Wiring: neutral not required
  • Load capacity: 50-250W (resistive load) or 0.25-1.1A (inductive load)
  • Lamp type  compatible (dimmable): Incandescent, CFL, Halogen (230VAC and 12VDC with electronic transformer), LED
  • Lamp type compatible (not dimmable): CFL, LED
  • Frequency: 868.42 Mhz
  • Signal strength: 1mW
  • Transmission distance: 50m free field, 30m indoor
  • Dimensions: 42.5 x 38.25 x 20.3mm
  • Operating temperature: 0-35 ° C
  • Temperature limit: 105 ° C
  • Standards: RoHS 2011/65 / EU, LVD 2006/95 / EC, EMC 2004/108 / EC R & TTE 1999/5 / EC

Manual:

 

 

Especificação

Compatibilidade controlador principal
eeDomus+ full compatible
Fibaro Home Center 2 v4.160 full compatible
Fibaro Home Center Lite v.4.160 full compatible
Vera Edge / Plus / Secure full compatible
Zipabox/Zipaminicro/ZipaTile full compatible
Piper / Piper NV (v.1.7.1) Not Tested
Indigo Not Tested
jeedom full compatible
Domoticz full compatible
ZiHome Not Tested
Tech Data
IP Rating IP 20
FLiRS No
Power Supply 230V
Attachable Loads 25 ... 400 W, lower at very inductive or resistive loads.
Explorer Frames - NWI Support Yes
SDK 4.52.00
App Version 3.3
Device Type Routing Multilevel Switch
Peper1 Database link http://pepper1.net/zwavedb/device/334
Z-Wave Alliance Product Link http://products.z-wavealliance.org/products/1729
Generic Device Class Multilevel Switch
Specific Device Class Multilevel Power Switch
Routing Yes

Perguntar

Fazer uma pergunta ou comentário

Obs: HTML não é suportado!

Mau            Bom


Continuar

Z-Wave Portugal

A loja online que vende soluções para a automação das habitações através das redes sem fios e do protocolo Z-Wave. Z-Wave é o standard internacional para as redes sem fio dos sistemas de controlo para habitações. Com base nestas soluções pode gerir a iluminação, a electricidade, os estores, os alarmes e muito mais, optimizando a utilização destes meios. Os produtos Z-Wave, mesmo os de diferentes fabricantes, funcionam bem em conjunto permitindo o controlo efectivo da casa inteligente.

Contact Us

Móvel:
+351 919655531
email:
info@z-wave.pt
Skype:
ar.alexandre.ramos

Twitter

Facebook