€ 34,95
Taxas não incluidas: € 28,88
Descrição
The Hank Z-Wave Plus Scene Controller is a wireless, portable and rechargeable device. It can control Z-Wave devices, such as a smart plug or intelligent dimmer after being included in a Z-Wave controller. You can also use it to activate scenes. This stage controller can perform 3 different actions per button, depending on the type of support: short press, support maintained, support released. Operating with a rechargeable battery with a range of 3 to 6 months, it will be very easy to recharge by connecting a USB cable on its micro-USB port. No need to change the batteries! In addition, this stage controller is equipped with a buzzer that will alert when the battery is low (less than 20%), or when communication has failed. An RGB LED is present to give visual information.
This stage controller is also equipped with the Z-Wave scope test function. A Z-Wave controller (remote control, dongle ...) is required to integrate this module into your network if you already have an existing network. ç
FUNCTIONS:
- Z-Wave + Scene Controller
- Control up to 3 devices / scenes per button
- Z-Wave Range Test Function
- Rechargeable battery
- Low battery warning and communication error (via buzzer)
- Security of radio communication via AES-128 encryption
- Integrates the Z-Wave 500 series chip
- Firmware Updates Over The Air (OTA)
- Ease of use and installation
TECHNICAL CHARACTERISTICS :
- Module Type: Z-Wave + 500 Series Transmitter
- Power supply: 3,6V rechargeable battery LIR2450
- Standby power consumption: 3uA
- Power consumption in operation: 36mA
- Frequency: 868.42 Mhz
- Transmission distance: 100m in free field, 30m indoors
- Dimensions: 50 x 50 x16 mm
- Operating temperature: 0 ° C to 40 ° C
- Certifications: FCC, CE, Z-Wave
- Z-Wave certification number: ZC10-16095219
Manual:
Especificação
| Compatibilidade controlador principal | |
|---|---|
| eeDomus+ | Full Compatible |
| Fibaro Home Center 2 v4.160 | Not Tested |
| Fibaro Home Center Lite v.4.160 | Not Tested |
| Vera Edge / Plus / Secure | Not Tested |
| Zipabox/Zipaminicro/ZipaTile | Not Tested |
| Piper / Piper NV (v.1.7.1) | Not Tested |
| Indigo | Not Tested |
| jeedom | Full Compatible |
| Z-Wave.me / Z-Way / PoPP Hub | Not Tested |
| Domoticz | Not Tested |
| ZiHome | Not Tested |
| Somfy Tahoma | Not Tested |
| Home Assistant | Not Tested |
| Telldus | Not Tested |
| Tech Data | |
| IP Rating | IP20 |
| FLiRS | No |
| Power Supply | Batterie rechargeable 3,6V LIR2450 |
| Explorer Frames - NWI Support | No |
| SDK | 6.51.08 |
| App Version | HW: 1 FW: 1.00 |
| Device Type | Wall Controller |
| Z-Wave Alliance Product Link | https://products.z-wavealliance.org/products/1968 |
| Procedures | |
| Incluison | Included as non-secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Waave network controller operating manul). 3. Triple click a button. 4. If the inclusion is successful, the LED will blink in blue less than for 5 seconds and then keep on for 15 seconds. Included as a secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual). 3. Pressing and holding a button for 3 seconds. 4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds. |
| Exclusion | To remove the Scene Controller from the Z-Wave network: (1) Insert the LIR2450 battery. (2) Set the Z-Wave network main controller into remove mode (see Z-Wave controller operating manual). (3) Triple click the a button, if the exclusion is successful, LED will blink in orange for less than 5 seconds and then keep on for 3 seconds. |
| Factory Reset | Pressing and holding a button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds. Using this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Wake Up | Pressing and holding a button for 3 seconds. Led will turn to green, which means Scene Controller has been woken up. |
