Wall Plug switch with metering and 2 USB ports Z-Wave Plus - Hank


Taxas não incluidas: € 33,02

Out Of Stock
Código do produto:


This smart plug is a Z-Wave module that simply installs between the device to be controlled and a wall outlet. It allows to control (on / off) any type of electrical device or lighting from its button located locally, or from any compatible Z-Wave controller.

Also incorporating the consumption measurement function, this socket can signal the wattage or energy usage in kWh to the Z-Wave controller. In addition, the consumption level of the connected load will be indicated visually by the integrated RGB LEDs creating a light ring. These RGB LEDs can also indicate the signal quality between the jack and the Z-Wave controller when using the Z-Wave Scope Test function. The Hank Z-Wave + smart plug is equipped with 2 USB ports (1A and 2.4A) that can charge smartphones or tablets.

This Z-Wave module also works as a wireless repeater with other modules, to ensure total coverage of your home. A Z-Wave controller (remote control, dongle ...) is required to integrate this module into your network if you already have an existing network.


  • Manage a lamp or a device remotely
  • Plug module integrating directly between an electrical outlet and the load to be controlled
  • ON / OFF function to control lamps or devices (no variation)
  • Measurement of instantaneous and cumulative consumption
  • Local load control via integrated button
  • 2 USB ports to charge smartphones or tablets
  • Z-Wave Scope Test Function Indicates consumption in real time thanks to its ring of light (7 color levels)
  • Overload protection
  • Security of radio communication via AES-128 encryption Integrates the Z-Wave 500 series chip
  • Firmware Updates Over The Air (OTA)
  • Z-Wave message repeater
  • Ease of use and installation


  • Module Type: Z-Wave + 500 Series Receiver
  • Power supply: 230VAC, 50Hz
  • Standby power consumption: 1.5W
  • Max load: 2300W / 10A
  • USB Outputs: DC 5V ± 5%, 1A (Port1), 2.4A (Port2)
  • Frequency: 868.42 Mhz
  • Transmission distance: 150m in free field, 40m indoors
  • Dimensions: 82 x 55 x 28 mm
  • Operating temperature: -10 ° C to 40 ° C
  • Certifications: FCC, CE, Z-Wave
  • Z-Wave certification no .: ZC10-16075153




Compatibilidade controlador principal
eeDomus+ Full Compatible
Fibaro Home Center 2 v4.160 Full Compatible
Fibaro Home Center Lite v.4.160 Full Compatible
Vera Edge / Plus / Secure Not Tested
Zipabox/Zipaminicro/ZipaTile Not Tested
Piper / Piper NV (v.1.7.1) Not Tested
Indigo Not Tested
jeedom Full Compatible
Z-Wave.me / Z-Way / PoPP Hub Not Tested
Domoticz Not Tested
ZiHome Not Tested
Somfy Tahoma Not Tested
Home Assistant Not Tested
Telldus Not Tested
Tech Data
IP Rating IP20
Power Supply 230VAC, 50Hz
Attachable Loads 2300W / 10A
Explorer Frames - NWI Support Yes
SDK 6.51.08
App Version HW: 1 FW: 1.00
Device Type On/Off Power Switch
Z-Wave Alliance Product Link https://products.z-wavealliance.org/products/1891
Incluison 1) Connect the power supply. 2) Set the Z-Wave network main controller into inclusion mode (see Z-Wave network controller operating manual). 3) Triple click the Z-button or power up the device , RGB LED indicator should blink fast in blue. 4) Smart Plug should be recognized and included into the Z-Wave network.
Exclusion 1) Insert the Plug into a socket. 2) Set the Z-Wave network controller into the exclusion mode (see Z-Wave controller operating manual). 3) Triple click the Z button. 4) RGB LED indicator will blink orange till the removing process is completed, than the indicator will keep orange for 3 seconds.
Factory Reset 1) Insert the Plug into a socket, 2) Press and hold the Z button for more than 20 seconds, 3) If holding time more than 20seconds, the RGB LED indicator will keep yellow for 2 seconds, which means resetting is completed. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.


Fazer uma pergunta ou comentário

Obs: HTML não é suportado!

Mau            Bom


Z-Wave Portugal

A loja online que vende soluções para a automação das habitações através das redes sem fios e do protocolo Z-Wave. Z-Wave é o standard internacional para as redes sem fio dos sistemas de controlo para habitações. Com base nestas soluções pode gerir a iluminação, a electricidade, os estores, os alarmes e muito mais, optimizando a utilização destes meios. Os produtos Z-Wave, mesmo os de diferentes fabricantes, funcionam bem em conjunto permitindo o controlo efectivo da casa inteligente.

Contact Us

+351 919655531