€ 64,13
Taxas não incluidas: € 53,00
Descrição
Micromodule switch Z-Wave + FIBARO Double Switch 2
The Fibaro Double Switch 2 has been designed to activate and deactivate electrical appliances. Thanks to its small size, it can be installed in junction boxes or recessed boxes. The module is controlled either by the Z-Wave network or a simple switch. Power and power metering allows you to monitor and reduce your electricity bills. Connect your FIBARO Double Switch 2 to your Z-Wave system and other devices to enjoy almost endless possibilities!
Software Updates
You can update the software of your Fibaro Double Switch 2 to the latest version once it is available. This way, you have access to the latest features without having to buy the latest version of the device.
Easy to install
Simply place the module into the flush-mounting box and connect it to an existing installation. The miniature size of the module allows you to place it in many convenient locations.
To summarize
The Double Switch 2 is not only one but two steps forward in managing your smart home. The Z-Wave 500 series chip and the Z-Wave Plus protocol offer capabilities that were previously unavailable. The power and energy measurement function allows you to optimize your electricity bills. By making use of the scene activation mechanism, you can tailor your home to your preferences.
Note: This module requires the Neutral to operate. The output is not potential-free, it does not allow to control a dry contact or load another supply voltage than the input.
FEATURES:
- Manage two lights / appliances remotely
- Installs behind an existing switch
- ON / OFF function
- Integrates Z-Wave chip 500 series
- Communication 250% faster compared to standard Z-Wave devices
- Integrated scene activation mechanism
- Safety and notification communication classes
- Setup menu with a diode
- Measurement of energy and power of connected devices
- Supports secure mode (Safety Z-Wave network) encrypted with AES-128 encryption
- Cover tester integrated Z-Wave network
- Last OTA software update (depends on the controller)
- Larger terminals for easy wiring
- Rounded to meet the highest standards
- Use back and forth
- Use in place of a remote control switch
- Small, discreet and aesthetic
- Ease of use and installation
TECHNICAL FEATURES :
- Module Type: receiver Z-Wave
- Power supply: 100 - 240V ~ 50 / 60Hz
- Wiring: 3 son, Neutral necessary
- Maximum power: 6.5A per channel, total 10A (resistive load only)
- Frequency: 868.42 Mhz
- Transmission distance: 50m free field, 40m indoors
- Signal strength: 1mW
- Dimensions: 42,5mm x 20,3mm x 38,25mm (L x W x H)
- Operating temperature: 0-35 ° C
- Standards:
- EMC 2014/30 / EU
- RED 2014/53 / EU
- RoHS 2011/65 / EU
- LVD 2014/35 / EU
Especificação
| Compatibilidade controlador principal | |
|---|---|
| eeDomus+ | |
| Fibaro Home Center 2 v4.160 | Full compatible |
| Fibaro Home Center Lite v.4.160 | Full compatible |
| Zipabox/Zipaminicro/ZipaTile | |
| Piper / Piper NV (v.1.7.1) | |
| Indigo | |
| jeedom | |
| ZiHome | |
| Tech Data | |
| Explorer Frames - NWI Support | Yes |
| SDK | 6.51.06 |
| App Version | 3.2 |
| Device Type | On/Off Power Switch |
| Z-Wave Alliance Product Link | http://products.z-wavealliance.org/products/1742 |
| Procedures | |
| Incluison | 1) Switch off the mains voltage (disable the fuse). 2) Place the Switch 2 within the direct range of your Z-Wave controller. 3) Connect the device in accordance with one of the diagrams attached in the manual. 4) After verifying correctness of the connection switch on the mains voltage. 5) Identify the S1 switch or the B-button (located on the device’s housing). 6) Set the main controller in (security/non-security) add mode (see the controller’s manual). 7) Quickly, three times press the S1 switch or the B-button. 8) Wait for the adding process to end. 9) Successful adding will be confirmed by the Z-Wave controller’s message. |
| Exclusion | 1) Place the Switch 2 within the direct range of your Z-Wave controller. 2) Identify the S1 switch or the B-button (located on the device’s housing). 3) Set the main controller in remove mode (see the controller’s manual). 4) Quickly, three times press the S1 switch or the B-button. 5) Wait for the removing process to end. 6) Successful removing will be confirmed by the Z-Wave controller’s message. |
| Factory Reset | Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. In order to reset the device: 1) Switch off the mains voltage (disable the fuse). 2) Remove the Switch 2 from the wall switch box. 3) Switch on the mains voltage. 4) Press and hold the B-button to enter the menu. 5) Wait for the visual LED indicator to glow yellow. 6) Quickly release and click the B-button again. 7) After few seconds the device will be restarted, which is signalled with the red LED indicator colour. Use reset procedure only if the primary controller is missing or inoperable. |
| Wake Up | The FIBARO Double Switch 2 is powered with mains voltage so it is always awake. |
