€ 189,90
Taxas não incluidas: € 156,94
Descrição
Although equipped with an LCD screen for displaying measurements, this module can also trace its various measurements to the Z-Wave home automation controller. In addition, it acts as a repeater to improve the range and stability of the Z-Wave network.
The module can also control electrical devices (switching on / off) with the addition of the following external relays:
- BICOM432-40-WM1 bistable switch (32A), controlled by optical communication port (IR)
- Contactor (32A) IKA232-20 / 230V controlled by the output on terminal 5
Finally, it should be noted that the brand QUBINO has set itself obligations of quality and durability: they have carefully selected high-performance components. Numerous quality control tests have also been performed on the module to ensure maximum durability (resistant enough to operate at temperatures from -10 ° C to 40 ° C).
FEATURES:
- Measurement of the overall consumption of a three-phase electrical installation.
- Measurement of the consumption of an electrical appliance operating in three-phase (heat pump, induction furnace, ...).
- Provides voltage, current, active, reactive, and apparent power, and power factor data.
- Integrates the Z-Wave 500 series chip (Z-Wave +)/ 250% faster communication compared to standard Z-Wave devices.
- LCD display screen (7 + 1 digit, 100Wh resolution).
- Operating temperature -10 to 40 ° C.
- Optical communication port (IR) for BICOM432-40-WM1 external relay.
- Output for connecting an IKA232-20.
- 230 V external contactor.
- Installation in the electrical panel
TECHNICAL CHARACTERISTICS:
- Power supply: 3X230V / 400V
- Consumption: <8VA
- Reference current (Iref): 5 A
- Maximum current (Imax): 65 A
- Minimum current (Imin): 0.25 A
- Starting current: 20 mA
- Detail:
- Power and active energy:
- Standard EN 62053-21: Class 1
- Standard EN 50470-3: Class B
- Reactive energy:
- Standard EN 62053-23: Class 2
- Power and active energy:
- Detail:
- Radio transmission frequency: 868.42MHz, Z-Wave
- Range: up to 30 m indoors (depending on surrounding materials)
- Operating temperature: -10 ~ 55 ° C
- IP protection: IP20
Especificação
Compatibilidade controlador principal | |
---|---|
eeDomus+ | not tested |
Fibaro Home Center 2 v4.160 | not tested |
Fibaro Home Center Lite v.4.160 | not tested |
Vera Edge / Plus / Secure | not tested |
Zipabox/Zipaminicro/ZipaTile | not tested |
Piper / Piper NV (v.1.7.1) | not compatible |
Indigo | not tested |
jeedom | not compatible |
Z-Wave.me / Z-Way / PoPP Hub v 3.2.1 | Full compatible |
Domoticz | not tested |
ZiHome | not tested |
Somfy Tahoma | not tested |
Home Assistant | not tested |
Telldus | not tested |
Tech Data | |
IP Rating | IP 20 |
Power Supply | 230 Vac |
Attachable Loads | 80 A |
Explorer Frames - NWI Support | |
SDK | |
App Version | |
Device Type | |
Procedures | |
Incluison | 1. Connect the module to the power supply 2. Enable inclusion mode on controller and press and hold the S (Service) button for at least 2 seconds 3. A new device will appear on your dashboard |
Exclusion | 1. Connect the module to the power supply 2. Enable exclusion mode on your Z-Wave controller and press and hold S (Service) button for at least 2 to 6 seconds. 3. The module will be excluded from your network but any custom configuration parameters will not be erased. |
Factory Reset | 1. Connect the module to the power supply 2. Within the first minute the module is connected to the power supply, press S (Service) button at least 6 to 20 seconds By resetting the module, all custom parameters previously set on the module will return to their default values, and the owner ID will be deleted. Use this reset procedure only when the main controller is missing or otherwise inoperable. |